首先打开包装后，检查节能电炉是否完整无损，配件是否齐全。一般的节能电炉不需要特殊安装，只需平放在室内平整的地面或搁架上。控制器应避免震动，放置位置与电炉不宜太近，防止因过热而造成内部元件不能正常工作。

在电源线引入处需要另外安装电源开关，以便控制总电源。为了保证安全操作，电炉与控制器必须可靠接地。上控制器外壳。将温度指示仪的设定指针调整至所需要的工作温度，然后接通电源。打开电源开关，此时温度指示仪表上的绿灯既亮，继电器开始工作，电炉通电，电流表即有电流显示。随着电炉内部温度的升高，温度指示仪表指针也逐渐上升，此现象表明系统工作正常。在使用前，将温度表指示仪调整到零点，在使用补偿导线及冷端补偿器时，应将机械零点调整至冷端补偿器的基准温度点，不使用补偿导线时，则机械零点调至零刻度位，但所指示的温度为测量点和热电偶冷端的温差。

电炉的升温、定温分别以温度指示仪的红绿灯指示，绿灯表示升温，红灯表示定温。有热电偶插入炉膛20-50mm，孔与热电偶之间空隙用石棉绳填塞。高温电炉连接热电偶至控制最好用补偿导线（或用绝缘钢芯线），注意正负极，不要接反。